FL-2 DC 75mV 50A Shunt Resistor For Meter Amp Analog Panel Ammeter VoltMeter

The fixed setpoint shunt is a suitable the attached external shunt for measuring DC current in 10kA less directly acting on the analog display instrument together with the use in order to expand the scope of the DC current measurement, or sequentially circuit can be regarded as the current sampling with the standard resistors, a sampling voltage is measured with a current can be regarded as an analog signal.

 

Specifications:

 

1.Accuracy level :2-4000A, 0.5 level；5000-10000A， 1 level.

 

2.Environmental conditions: -40 ~ +60 ℃, the relative temperature ≤ 95% (35 ° C)

 

3.Overload performance: 120% of rated current, 2 hours

 

4.Voltage drop: 75mV

 

5.Load heat: Temperature rise changes stabilized, rated current of 50A does not exceed 80 ° C; rated current of 50A does not exceed 120 ° C.

 

Weight: 72g 

Dimension (L x W x H): (Approx.)  12cm x 2.6cm x 1.8cm
 

Package included:1 x 50A 75mV DC Shunt Resistor

Xilinx Platform USB Download Cable Jtag Programmer for FPGA CPLD C-Mod XC2C64A

Xilinx Platform USB Download Cable Jtag Programmer for FPGA CPLD C-Mod XC2C64A

.Support all Xilinx devices:        All Virtex FPGA families        All Spartan FPGA families        XC9500/XC9500XL/XC9500XV CPLDs         CoolRunner XPLA3/ CoolRunner-II CPLDs         XC 18V00 ISP PROMs          XCF00S/XCF00P Platform Flash PROMs          XC4000 series FPGAs 3. Supported on Windows and Red Hat Enterprise Linux 4. Work with impact , chipscope pro and microblaze embedded processer debuging 5.support target system using 5.0V TTL,3.3V LVTTL/LVCMOS, 2.5V, 1.8V,1.5V 6. Apply to Xilinx CPLD / FPGA chips download debugging. 7. Support JTAG, Slave Serial, SPI download mode, can configure all Xilinx devices. 8. Xilinx Platform with USB Cable fully compatible. 9. Target device to download the clock options, up to 24MHz. 10. Support iMPACT and ChipScope. 11. Firmware can be updated automatically.

 NB: Device intended for advanced users, handle with care and read all available documents before using

Package :

1 x USB Download and Programmer Adapter   1 x 6-pin 2.54mm  flat cable,  1 x 10-pin 2.54mm pitch 15cm flat cable,    1 x 14-pin 2.0mm pitch 15cm flat cable, 1 x 14-pin 2.54mm pitch 15cm flat cable 1x 7-pin fly duppont cables 1x cable adapter  1 x USB Cable

TEC1-12706 Thermoelectric Cooler Peltier 12V 60W 92Wmax

Rated voltage: 12v 
Rated current of 4.5A, 
Power :50 - 60W 
Maximum temperature: 60o Celsius 
Dimensions: 4x4x0.4cm 

Connected to a 12-volt power supply the cell will have a temperature differential between the two sides of about 20oC(68oF). 
Important: do not connect the cell to a power supply for more than a few seconds without a heat-sink on the hot side otherwise there will be internal overheating and destruction of the Peltier cell. 

Installation 
This cooling Peltier cell is very simple to install and use. 
Before installation, you must provide a dry environment and allow for any condensation from the cold side to drain away and not to come in contact with the operating cell. 
Connect the two leads of the Peltier cell to an appropriate power supply and importantly, observe the correct lead polarity and attach an adequate heat-sink with a quality thermal conducting grease applied to the warm side of the cell; you will feel the warm side and the opposite cool side of the operating cell. It is important to identify both the correct lead polarity and the cooling/heating sides of the device. 
If you want a greater cooling differential, it is recommended to use two Peltier cells, namely, one stacked above the other with the hot side of the upper cell in contact with the cool side of the lower one; an experiment proved the two stacked cell cooling effect is much better than the single-stage. Similarly a three cell stack produces an even greater temperature differential but requires a larger capacity power supply support.